天气清冷之前，机械该如何进行保养呢？冷再生机出租厂家这里为您简单的讲一讲。

How to maintain the machinery before the cold weather? Here is a brief talk for you from the cold recycling machine rental manufacturer.

一、清洗外表

1、 Clean the surface

1.冷再生机在施工过程中会有大量的灰尘落到再生机的表面，包括施工中沾污的油迹等污染物，影响外观事小，更为严重的是成为腐蚀的诱发因素。

1. During the construction of the cold regenerator, a large amount of dust will fall on the surface of the regenerator, including pollutants such as oil stains stained during the construction, which will have little impact on the appearance, and more seriously, will become a corrosion inducing factor.

1.清洗工程机械的柴油机、底盘、工作装置的外表,除垢、除油保持再生机的外观整洁。

1. Clean the appearance of the diesel engine, chassis and working device of the construction machinery, remove dirt and oil, and keep the appearance of the regenerator clean.

2.清洗时严禁用高压、高温的水枪来冲洗防水要求较高的部位（特别是电器部分），以免造成电器部分的损坏。

2. It is forbidden to use high-pressure and high-temperature water gun to wash parts with high waterproof requirements (especially electrical parts) during cleaning, so as to avoid damage to electrical parts.

二、保养转子及其罩壳和滑靴

2、 Maintain the rotor and its casing and slippers

1.检查转子是否有水泥结垢等，及时清理灰尘，对需要割除、焊接的刀具及时更换；

1. Check whether there is cement scaling on the rotor, clean up the dust in time, and replace the cutters that need to be cut and welded in time;

2.清理转子罩壳上的灰尘，并在施工结束收车时将转子罩壳垫起地面5-10公分，防止雨雪的浸蚀；

2. Clean the dust on the rotor housing, and pad the rotor housing 5-10cm above the ground at the end of construction to prevent rain and snow erosion;

3.检查滑靴，对已经磨损的滑靴部分进行补焊，螺纹处应涂抹黄油防锈。

3. Check the sliding shoes, repair the worn sliding shoes, and apply grease on the threads to prevent rust.

三、减速机油位及减速机油的检查

3、 Inspection of reducer oil level and reducer oil

先切断电源，等待减速机冷却后打开放油螺塞，检查油是否充满，避免漏油，取油样，检查油色泽及粘度指数，如果油明显浑浊，建议尽快更换。新减速机使用后（500-1000）小时更换新油（将内部污油冲干净），其后每使用1500小时需要更换油一次，但是在使用过程中，仍需要检查油的质量，若油有老化、变质情况要随时更换。）

First cut off the power supply, wait for the reducer to cool down, open the oil drain plug, check whether the oil is full, avoid oil leakage, take an oil sample, check the oil color and viscosity index, if the oil is obviously turbid, it is recommended to replace it as soon as possible. The new reducer shall be replaced with new oil (flushing the dirty oil inside) within (500-1000) hours after use, and the oil shall be replaced every 1500 hours after use. However, the oil quality shall still be checked during use, and the oil shall be replaced at any time in case of aging and deterioration.)

天冷前的冷再生机怎么保养呢？以上就是问题的我相关解答了，您对此有什么想了解的就来我们网站http://www.tclqgc.com咨询吧！

How to maintain the cold rebirth before cold weather? The above is my answer to the question. If you want to know anything about it, please come to our website http://www.tclqgc.com Consult!