冷再生机保养的内容主要是清洁、紧固、调整、润滑、防腐。为了让大家更好的去使用，下面冷再生机出租厂家为您分析：

The maintenance of the cold regeneration machine mainly includes cleaning, tightening, adjustment, lubrication, and anti-corrosion. In order to help everyone better use it, the rental manufacturer of the cold regeneration machine will analyze for you:

例行保养以清洁、润滑、检查和紧固为中心，在每班出车前、工作中及收车后都要按要求进行例行保养。根据冷再生机设备的保养要求，在达到规定的工作小时或规定的里程后，必须进行相应的定期保养，包括以下内容:

Routine maintenance focuses on cleaning, lubrication, inspection, and tightening, and must be carried out as required before, during, and after each shift. According to the maintenance requirements of the cold regeneration machine equipment, after reaching the specified working hours or mileage, corresponding regular maintenance must be carried out, including the following contents:

工作内容是润滑、紧固并检查各有关部位以及清洁“三滤”工作(即清洁空气、机油、燃油滤清器等)。

The key work content is lubrication, tightening, and inspection of all relevant parts, as well as cleaning the "three filters" (i.e. cleaning air, oil, fuel filters, etc.).

以检查、调整为具体要检查发动机、离合器、变速器、传动机构、转向和制动机构、工作装置、液压系统以及电气系统等工作情况并进行必要的调整，排除所发现的故障,保障机械各总成、零部件具有良好的工作性能。

Focusing on inspection and adjustment, it is necessary to inspect the working conditions of the engine, clutch, transmission, transmission mechanism, steering and braking mechanism, working device, hydraulic system, and electrical system, and make necessary adjustments to eliminate any faults found and ensure that all mechanical assemblies and components have good working performance.

是检测、调整、排除故障隐患及平衡各部机件的磨损程度。要对影响使用性能的部位及有故障征兆的部位进行诊断检查、状态性检测，进而完成必要的更换、调整及故障排除等工作。

The key is to detect, adjust, eliminate potential faults, and balance the wear level of each component. Diagnostic checks, status checks, and necessary replacements, adjustments, and troubleshooting should be carried out on parts that affect the performance of the equipment and those with signs of failure.

新机或大修后的冷再生机在走合期内必须进行走合保养。机械在规定的走合期内使用时，需按相应规程逐级递增负载及转速，并检查润滑、紧固情况，观察整机各部状况，发现异常及时解决。走合保养的是更换各部润滑油、润滑各部位、紧固各螺栓。

During the running in period, maintenance must be carried out for new or overhauled cold air engines. When the machinery is used within the specified running in period, it is necessary to gradually increase the load and speed according to the corresponding regulations, and comprehensively check the lubrication and fastening conditions. Observe the condition of all parts of the machine, and promptly solve any abnormalities found. The key to running in maintenance is to replace the lubricating oil of each part, lubricate each part, and tighten each bolt.

冷再生机每年入夏或入冬前应进行一次换季保养。是燃润系统、液压系统、冷却系统和启动系统等部分。需根据实际情况做好以下工作:更换燃润油料及液压油、调整蓄电池电解液的相对密度、采取防寒或降温措施及清洗冷却系统等。

The cold regeneration machine should undergo seasonal maintenance once a year before entering summer or winter. The focus is on the fuel lubrication system, hydraulic system, cooling system, and starting system. The following work needs to be done according to the actual situation: replacing fuel and hydraulic oil, adjusting the relative density of battery electrolyte, taking cold or cooling measures, and cleaning the cooling system.

在机械设备因季节因素(如冬休期)等需要停用一段时间时应进行停用保养。主要做好清洁、整容、配套、防腐等工作。更多相关事项就来我们网站http://www.tclqgc.com咨询！

When mechanical equipment needs to be discontinued for a period of time due to seasonal factors (such as winter break), maintenance should be carried out. Mainly responsible for cleaning, cosmetic surgery, matching, anti-corrosion and other work. For more related matters, come to our website http://www.tclqgc.com consulting service