WR2300E路面冷再生机是WR2300L型路面冷再生的升级型号，机器实现了全电控化操作，实现自动喷水功能，双方向盘操作，适用于高强度水泥稳定层的路面冷再生施工。

The WR2300E road surface cold regeneration machine is an upgraded model of the WR2300L road surface cold regeneration. The machine realizes fully electronic control operation, automatic water spraying function, dual steering wheel operation, and is suitable for cold regeneration construction of high-strength cement stabilized layers.

●·康明斯KTA19-C600柴油发动机，额定功率600马力，适应国内柴油，动力强劲，功率贮备大，可靠性高，维护保养方便;●·可靠的散热系统，夏季发动机不高温，液压油温不超过60度，泵马达始终处于工作温区;

Cummins KTA19-C600 diesel engine with a rated power of 600 horsepower, suitable for domestic diesel, strong power, large power reserve, high reliability, and convenient maintenance; ● Reliable heat dissipation system, the engine is not hot in summer, the hydraulic oil temperature does not exceed 60 degrees, and the pump motor is always in the working temperature zone;

●·液压系统采用德国萨澳丹佛斯( Sauer Danfoss）系统，可靠性高;

The hydraulic system adopts the Sauer Danfoss system from Germany, which has high reliability;

●转子驱动采用美国原装大扭矩减速机，转子转速设有三个工作挡，可跟据工况要求，调整铣刨鼓转速，在满足破碎粒度要求的同

The rotor drive adopts an American original high torque reducer, and the rotor speed is set in three working gears. The milling drum speed can be adjusted according to the working conditions, while meeting the requirements of crushing particle size

时，避免混合料离析，提高工作速度，使机器处于工作状态;档(大扭矩)，适用于高强度沥青水泥稳定层破碎（碎石路基)等冷再生高负荷工况，I档和Ⅲ挡适用于沥青灰土路基冷再生等低强度路基冷再生，破碎粒度小，颗粒更细;

To avoid segregation of the mixture, increase the working speed and keep the machine in working condition; Gear (high torque), suitable for high-strength asphalt cement stabilized layer crushing (crushed stone subgrade) and other cold regeneration high load conditions. Gear I and III are suitable for low strength subgrade cold regeneration such as asphalt ash soil subgrade, with smaller crushing particle size and finer particles;

●·重型铣刨鼓经强化设计，采用焊接基座，可更换刀库（齿套)，刀齿三件组合型式。刀库（齿套）均为可拆式，刀齿与刀库磨损

The heavy-duty milling and planing drum is reinforced with a welded base, replaceable tool magazine (gear sleeve), and a three piece combination of tool teeth. The tool magazine (gear sleeve) is detachable, and the tool teeth and tool magazine are worn out

后均可在现场快速更换，适应高强度的连续水稳路基冷再生施工;铣刨刀齿采用22型，使用寿命长，更耐磨损﹔铣刨鼓经动平衡调整,采用专用检具检测，装配精度高，运转平稳;

Afterwards, it can be quickly replaced on site to adapt to high-strength continuous water stable roadbed cold regeneration construction; The milling cutter teeth are of type 22, which has a long service life and is more wear-resistant. The milling drum is adjusted for dynamic balance and tested with specialized inspection tools, resulting in high assembly accuracy and smooth operation;

●·机器行走设有三个档位，水稳路基冷再生采用行走I档，行走速度控制精确，高负荷工况操控方便，灰土路基冷再生采用行走Ⅱ

The machine has three gears for walking, and the cold regeneration of the water stabilized roadbed adopts the walking I gear, with precise speed control and convenient operation under high load conditions. The cold regeneration of the gray soil roadbed adopts the walking II gear

档,更大的速度调节范围，行走III档用于机器转场;

Gear, larger speed adjustment range, walking in gear III for machine transfer;

●·全电控双方向盘操作系统，图形数字显示多种工作参数，操控精确方便，机器可方便靠左侧或右侧贴边施工;

● Fully electronically controlled dual steering wheel operating system, with graphical and digital display of various working parameters, precise and convenient operation, the machine can be easily operated by pressing the left or right side edge for construction;

●·添加剂喷洒（喷水）采用电控自动调节，自动控制与手动控制可自由切换，控制方便，精确可靠，可随机器的行走速度自动调节

Additive spraying (water spraying) adopts electronic control automatic adjustment, which can be freely switched between automatic control and manual control. The control is convenient, precise and reliable, and can be automatically adjusted with the walking speed of the machine

喷水流量，停车自动停止喷水;

Spray water flow rate, automatically stop spraying water when parking;

●·饺接车身转向与转向后桥相配合，转向灵活，后桥具有一键自动回中功能，无论后桥转向位于何种角度，均可一键操作后桥转向

The dumpling body steering is coordinated with the steering rear axle, providing flexible steering. The rear axle has a one click automatic centering function, allowing for one click operation of the rear axle steering regardless of its angle

自动回中，大大降低操作人员疲劳强度，提高工作效率;

Automatic centering greatly reduces operator fatigue and improves work efficiency;

●·双桥四轮驱动，配以人字轮胎，驱动力强劲，适应各种路况作业;

● Double axle four-wheel drive, equipped with herringbone tires, strong driving force, suitable for various road conditions and operations;

●·加压液压油箱配以德国进口吸回油滤油器，经过多年的使用验证考核，是可靠的滤油系统，可长期保持液压系统的清洁度，是液

The pressurized hydraulic oil tank is equipped with a German imported suction oil filter. After years of use verification and assessment, it is a reliable oil filtering system that can maintain the cleanliness of the hydraulic system for a long time. It is a liquid

本文由冷再生机租赁友情奉献.更多有关的知识请点击:http://www.tclqgc.com真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated to the rental of cold recycling machines. For more information, please click: http://www.tclqgc.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned