冷再生机是专门针对沥青道路开展再生工艺的设备，然而设备的工作效率是与操作人员的正确操作分不开的，只有严格按照正规流程开展操作才能使设备发挥100%的效果，那么冷再生机的正确操作规程是什么呢？下面冷再生机出租厂家就来介绍一下。

A cold recycling machine is a device specifically designed for the recycling process of asphalt roads. However, the efficiency of the equipment is inseparable from the correct operation of the operators. Only by strictly following the formal process can the equipment achieve 100% effectiveness. So what is the correct operating procedure for a cold recycling machine? Let's introduce the rental manufacturers of cold regeneration machines below.

1.使用后控制面板时，需将开关调到后操控，此刻前控制面板无作用，除此之外每个小喷嘴开关能够使用后控制面板开启、关掉。

1. When using the rear control panel, it is necessary to set the switch to rear control. At this moment, the front control panel has no effect. In addition, each small nozzle switch can be turned on and off using the rear control panel.

2.设备不可以灌的过满，给油口盖务必关严，运送过程中防止沥青溢出。

2. The equipment cannot be overfilled, and the oil supply port cap must be tightly closed to prevent asphalt overflow during transportation.

3.设备在喷撒前必须要查验各阀门部位是否正确。添加设备内的热态沥青务必达标160~180℃的操作温度，远距离运送或工作时间太长，可应用升温设备保溫，但不可以作为熔油炉。

3. Before spraying, the equipment must be checked to see if all valve parts are correct. The hot asphalt added to the equipment must meet the operating temperature of 160~180 ℃. If transported over long distances or working for too long, heating equipment can be used for insulation, but it cannot be used as a melting oil furnace.

冷再生机往前行驶时，转子往上转动铣刨原道路材料，与此同时，水通过软管从联接的水车中运输进来，并在再生机的搅拌仓中喷撒。水的输送量根据微处理器操纵的泵送系统精准控制，以达标所需要的水分含量。

When the cold regeneration machine moves forward, the rotor rotates upwards to mill and plane the raw road materials. At the same time, water is transported through a hose from the connected water truck and sprayed in the mixing bin of the regeneration machine. The delivery amount of water is accurately controlled by a microprocessor operated pumping system to meet the required moisture content.

铣刨转子将水与铣刨料充足拌合。液体稳定剂可根据布置的喷撒嘴被喷撒到搅拌腔；粉末

The milling rotor adequately mixes water with the milling material. The liquid stabilizer can be sprayed into the mixing chamber according to the professionally arranged spray nozzle; powder

稳定剂如混凝土需按布置填加量事前喷洒在冷再生机前的道路上，冷再生机将粉末状稳定剂与再生料和水一次性搅拌。如遇再造层原配合比欠佳的状况，可在再生前将所缺乏的部分集料喷洒在道路上，根据与废料加工搅拌来改进原地面材料的级配。

Stabilizers such as concrete need to be sprayed on the road in front of the cold recycling machine in advance according to the arrangement and dosage. The cold recycling machine will mix the powdered stabilizer with recycled materials and water in one go. If the original mix ratio of the reconstructed layer is not good, the missing part of the aggregate can be sprayed on the road before regeneration, and the grading of the original ground material can be improved by mixing it with waste processing.

以上就是冷再生机操作规程介绍的全部内容了，有关其操作流程就简介这么多了，特性就是低成本、不毁坏地基等。希望文中的简介能对大家有帮助。您有需求就来我们网站http://www.tclqgc.com咨询！

The above is the entire content of the introduction to the operating procedures for cold revitalization, and there are so many introductions about its operating procedures, with the characteristics of low cost and no damage to the foundation. I hope the introduction in the article can be helpful to everyone. Come to our website if you have any needs http://www.tclqgc.com consulting service